ASSEMBLY DIAGRAMS
26.75”
13.5”
17.25”
17.25”
P
5.75” 5.75”
11.5”
5.25”
G
A
J
D
A
UA
17.25”
17.25”
5.75” 5.75”
11
11.5”
G
A
D
B
B
B
BV
11.5”
K
B
E
H
54.5”
C
11.5”
B
E
H
= S tand-off
26.75”
26.75”
C
C
C W
69”
13.5”
= S tand-off 13.5”
= Cr oss- Clamp
D
11.5”
P
F
= Rod = Connector Tube
= Cr oss- Clamp
d-off
5.25”
5.25”
D
D
DX
A
A
UA
= Rod
11.5”
s- Clamp
= S tand-off Loca tions
= Connector Tube
DIAMOND
FAN
= S tand-off Loca tions GRID
11.5”
BV
B
E
Y
Y
Line H Line H
F
L
I
C
Line H
6”
TRELLIS COMPONENTS
54.5”
F
I
C
Line H
Hanger Bolt
Stand-O ff F itting
tting
Hanger Bolt
Stand-O ff F itting
Connector Tube = S tand-off
Cr oss- Clamp F itting
M achine T h r eads
e
Low P osition Hole
M achine T h r eads
C
C W
Low P osition Hole
Low P osition Hole
Screw T h r eads
ew
S etsc rew
Screw T h r eads
S etsc rew
S etsc rew
Hanger Bolt
Connector Tube
Stand-O ff F itting
= Cr oss- Clamp
High P osition Hole Cr oss- Clamp F itting STAND-OFF FITTING Low P osition Hole
Hex Nut
Ro ds inse rt into b oth ends
M achine T h r eads CROSS-CLAMP FITTING
Hex Nut CONNECTOR TUBE
High P osition Hole
Low P osition Hole High P osition Hole
= Rod = Connector Tube
Screw T h r eads
S etsc rew
S etsc rew
Ro ds inse rt into b oth ends
High P osition Hole
Hex Nut
High P osition Hole
TRELLIS COMPONENT & FASTENER SPECIFICATIONS Component Alloy D
DX
Specification
= S tand-off Loca tions
Rods (1/8” diameter)
Type 316 Stainless Steel
AISI Type 316, ASTM A492
Micro Cross-Clamps, Stand-Off Fittings (2”)
Type 316 Stainless Steel
AISI Type 316, ASTM A492
E
Y
Line H
Line H
6”
6”
FASTENER SPECIFICATIONS
Fastener
Alloy
Specification ANSI/ASME B18.2.1-2012
Hanger Bolts, Locking Hex Nuts
Type 18-8 Stainless Steel
MAINTENANCE GUIDELINES Exposed trellis components should be cleaned periodically. Cleaning frequency will depend on the environmental conditions that the product is placed in. Feeney recommends our Stainless Steel Cleaner & Protectant Kit for maintaining stainless steel products. Alternatively, warm water and mild soap can be used. Rinse stainless steel cables, rods, and fittings with fresh water. Remove dust and dirt from exposed components with a soft cloth or sponge and a solution of mild soap and/or liquid detergent in water. Always use a soft, damp cloth to blot dry. High P osition Hole Avoid harsh solutions or abrasive cleaning compounds, included but not limited to: alkaline or acidic cleaners, solutions containing trisodium phosphate, phosphoric acid, hydroflouric acid, gasoline, benzene, acetone, carbon tetrachloride, certain deicing fluids, lacquer thinner or other strong solvents. Product should be cleaned when the trellis is shaded. Cr oss- Clamp F itting Low P osition Hole S etsc rew
See Warranty and Care brochure or scan the QR code to learn more about our product maintenance guidelines and warranty information.
Hanger Bolt
M achi
Screw T h r eads
Hex Nut
FEENEY IS A PROUD MEMBER OF:
EXECUTIVE BOARD
© 2025 Feeney, Inc. Consistent with our policy of continuing product improvement, we reserve the right to change product specifications without notice or obligation. v2/25
Powered by FlippingBook